Parts & Accessories

Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted. - DT Swiss Rear End Caps - QR x 135/142mm

Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

- Standard skewers fit either 130 or 135mm spaced hubs, unless listed as another length (i.e. 170mm) - 6061 machined lever with stainless steel pivot and laser-etched logo - All shafts are 5mm in diameter

125 piece assortment of precision machined axle spacers (0.5mm to 5mm thickness). - Outside Diameter of Spacers: 16mm - Inside Diameter of Spacers: 10mm Kit includes: - (10) - 0.5mm thick spacers - (30) - 1mm thick spacers - (30) - 2mm thick spacers - (25) - 3mm thick spacers - (15) - 4mm thick spacers - (15) - 5mm thick spacers

• 5mm skewer set (F+R hubs) • Standard 5mm Hex release • Black or Silver anodized finish • Chromoly axles

• 5-sided key locking skewer set • Chromoly axles • 6061 anodized aluminum • Includes seat and F+R wheel skewers • 95g (set)

• Replacement aluminum quick release skewers

• Rim strips for 20-inch fat bike rims • 80mm wide

• Replacement aluminum quick release skewers

- Supplies full wheel illumination for 700c/29in wheels and smaller - Approximately 40 hrs of battery life - Water resistant design - Includes 3 (AA) batteries - Sold individually (1 wheel) - Easy to install

- Eady to install - Spoke mounted - 2 per set

- Variable widths - Left: 32mm - Center: 52mm - Right: 32mm - Length: 116mm - Overall: 137mm

- Variable widths - Left: 32mm - Center: 52mm - Right: 36mm - Length: 120mm - Overall: 141mm

- Variable widths - Left: 32mm - Center: 52mm - Right: 35mm - Length: 119mm - Overall: 140mm

- Converts Schrader rims to Presta - Rubber - Sold individually

- Fits all freewheel hubs - Will not fit Cassette hubs - Type: STD Plastic - Color: Clear

- Replacement adjustable nut for three-speed internal hubs.

Replacement clear plastic spoke guard.

- Replacement freehub bodies include pawls and springs pre-installed - M-Pulse hubs: six pawls are equipped with Neodymium magnets engaging every 1.66 deg - E-Sync hubs: fast 8.18 deg engagement with reinforced high-torque pawls - HG 11sp road FH body

Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.

Ultra light bolt on thru axle, with a low profile 6mm head for Whisky forks and some others. See other manufacturers specifications for fitment questions. - Thread Length (mm): 12 - Thread Pitch: 1.5 - MT/CX: 125 x 15mm - MTB+: 135 x 15mm - Fat: 198 x 15mm - RD/CX: 120 x 12mm - Rear: 167 x 12mm

Replacement Cassette body for Origin8 hubs

- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity

Replacement axles for DT Swiss hubs.

Small component with a large impact. A poorly constructed or unsuitable tyre rim tape can be the cause of many punctures. It is especially important with hollow section rims to use a pressure-resistant rim band which covers the entire rim. The fabric-reinforced Continental Easy Tape rim protector is designed for use under high air pressure conditions. The various widths enable a perfect fit for all standard rims. The high pressure design for racing cyclists withstands up to 220 psi, without becoming deformed. The flat construction type also significantly eases the job of tyre fitting.

After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding.

- AL6061 alloy tubeless Presta valve - Includes 2 O-rings, one standard profile and one aero profile, for an airtight seal on any rim - Removable valve core for installing sealant - Additional replacement valve cores sold separately - Sold individually

Origin-8's Track Cog Lock Ring with left-handed threading and 1.29 x 24tpi in a chrome finish completes your basic track cog locking needs.

CNC machined from 6061-T6 aluminum alloy, Box One Schrader Valve Caps add a touch of style to any bike. Available in anodized red, blue, and black with laser-etched Box logos.

SRAM's Quick Releases hold your wheel tightly in place, are built for ease of use and made to last, too. You get a front and rear quick release.